 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MAC16D, MAC16M, MAC16N Preferred Device Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. http://onsemi.com Features * * * * * * * * Blocking Voltage to 800 Volts On-State Current Rating of 16 Amperes RMS at 80C Uniform Gate Trigger Currents in Three Quadrants High Immunity to dv/dt - 500 V/ms minimum at 125C Minimizes Snubber Networks for Protection Industry Standard TO-220AB Package High Commutating di/dt - 9.0 A/ms minimum at 125C Pb-Free Packages are Available* TRIACS 16 AMPERES RMS 400 thru 800 VOLTS MT2 G MT1 MARKING DIAGRAM MAXIMUM RATINGS (TJ = 25C unless otherwise noted) Rating Peak Repetitive Off-State Voltage (Note 1) (TJ = -40 to 125C, Sine Wave, 50 to 60 Hz, Gate Open) MAC16D MAC16M MAC16N On-State RMS Current (Full Cycle Sine Wave, 60 Hz, TC = 80C) Peak Non-Repetitive Surge Current (One Full Cycle Sine Wave, 60 Hz, TJ = 125C) Circuit Fusing Consideration (t = 8.3 ms) Peak Gate Power (Pulse Width 1.0 ms, TC = 80C) Average Gate Power (t = 8.3 ms, TC = 80C) Operating Junction Temperature Range Storage Temperature Range Symbol VDRM, VRRM 400 600 800 IT(RMS) ITSM 16 150 A A x A Y WW G = D, M, or N = Assembly Location = Year = Work Week = Pb-Free Package Value Unit V MAC16xG AYWW 1 2 TO-220AB CASE 221A-09 STYLE 4 3 I2t PGM PG(AV) TJ Tstg 93 20 0.5 -40 to +125 -40 to +150 A2sec W W C C 1 2 3 4 PIN ASSIGNMENT Main Terminal 1 Main Terminal 2 Gate Main Terminal 2 Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 1. VDRM and VRRM for all types can be applied on a continuous basis. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. ORDERING INFORMATION Device MAC16D MAC16DG MAC16M MAC16MG MAC16N MAC16NG Package TO-220AB TO-220AB (Pb-Free) TO-220AB TO-220AB (Pb-Free) TO-220AB TO-220AB (Pb-Free) Shipping 50 Units / Rail 50 Units / Rail 50 Units / Rail 50 Units / Rail 50 Units / Rail 50 Units / Rail *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. Preferred devices are recommended choices for future use and best overall value. (c) Semiconductor Components Industries, LLC, 2005 1 December, 2005 - Rev. 3 Publication Order Number: MAC16D/D MAC16D, MAC16M, MAC16N THERMAL CHARACTERISTICS Characteristic Thermal Resistance, Junction-to-Case Junction-to-Ambient Symbol RqJC RqJA TL Value 2.0 62.5 260 Unit C/W C Maximum Lead Temperature for Soldering Purposes 1/8 from Case for 10 Seconds ELECTRICAL CHARACTERISTICS (TJ = 25C unless otherwise noted; Electricals apply in both directions) Characteristic OFF CHARACTERISTICS Peak Repetitive Blocking Current (VD = Rated VDRM, VRRM; Gate Open) ON CHARACTERISTICS Peak On-State Voltage (Note 2) (ITM = 21 A Peak) Gate Trigger Current (Continuous dc) (VD = 12 V, RL = 100 W) MT2(+), G(+) MT2(+), G(-) MT2(-), G(-) Holding Current (VD = 12 V, Gate Open, Initiating Current = 150 mA) Latching Current (VD = 24 V, IG = 50 mA) MT2(+), G(+) MT2(+), G(-) MT2(-), G(-) Gate Trigger Voltage (VD = 12 V, RL = 100 W) MT2(+), G(+) MT2(+), G(-) MT2(-), G(-) DYNAMIC CHARACTERISTICS Rate of Change of Commutating Current, See Figure 10. (VD = 400 V, ITM = 6.0 A, Commutating dv/dt = 24 V/ms, Gate Open, TJ = 125C, f = 250 Hz, No Snubber) (di/dt)c CL = 10 mF LL = 40 mH dv/dt 500 - - V/ms 9.0 - - A/ms VTM IGT 10 10 10 IH IL - - - VGT 0.5 0.5 0.5 0.75 0.72 0.82 1.5 1.5 1.5 33 36 33 50 80 50 V - 16 18 22 20 50 50 50 50 mA mA - 1.2 1.6 V mA TJ = 25C TJ = 125C IDRM, IRRM mA - - - - 0.01 2.0 Symbol Min Typ Max Unit Critical Rate of Rise of Off-State Voltage (VD = Rated VDRM, Exponential Waveform, Gate Open, TJ = 125C) 2. Indicates Pulse Test: Pulse Width 2.0 ms, Duty Cycle 2%. http://onsemi.com 2 MAC16D, MAC16M, MAC16N Voltage Current Characteristic of Triacs (Bidirectional Device) + Current Quadrant 1 MainTerminal 2 + Symbol VDRM IDRM VRRM IRRM VTM IH Parameter Peak Repetitive Forward Off State Voltage Peak Forward Blocking Current Peak Repetitive Reverse Off State Voltage Peak Reverse Blocking Current Maximum On State Voltage Holding Current Quadrant 3 MainTerminal 2 - IH VTM IRRM at VRRM on state IH VTM off state + Voltage IDRM at VDRM Quadrant Definitions for a Triac MT2 POSITIVE (Positive Half Cycle) + (+) MT2 (+) MT2 Quadrant II (-) IGT GATE MT1 REF (+) IGT GATE MT1 REF Quadrant I IGT - (-) MT2 (-) MT2 + IGT Quadrant III (-) IGT GATE MT1 REF (+) IGT GATE MT1 REF Quadrant IV - MT2 NEGATIVE (Negative Half Cycle) All polarities are referenced to MT1. With in-phase signals (using standard AC lines) quadrants I and III are used. http://onsemi.com 3 MAC16D, MAC16M, MAC16N 125 120 TC, CASE TEMPERATURE ( C) 115 110 105 100 95 90 85 80 0 2 6 8 10 12 IT(RMS), RMS ON-STATE CURRENT (AMP) 4 14 16 = 180 = 30 and 60 = 90 = 120 20 PAV, AVERAGE POWER (WATTS) 18 16 14 12 10 8 6 4 2 0 0 2 4 6 8 10 12 IT(RMS), ON-STATE CURRENT (AMP) 14 16 = 30 DC 180 120 90 60 DC Figure 1. RMS Current Derating Figure 2. On-State Power Dissipation 100 r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED) 1 TYPICAL AT TJ = 25C MAXIMUM @ TJ = 125C 0.1 I T, INSTANTANEOUS ON-STATE CURRENT (AMP) 10 0.01 0.1 1 10 100 t, TIME (ms) 1000 1*10 4 Figure 4. Thermal Response MAXIMUM @ TJ = 25C 1 40 I H, HOLD CURRENT (mA) MT2 POSITIVE MT2 NEGATIVE 0.1 0 0.5 1 1.5 2 2.5 3 3.5 VT, INSTANTANEOUS ON-STATE VOLTAGE (VOLTS) 4 5 -40 -10 20 50 80 TJ, JUNCTION TEMPERATURE (C) 110 125 Figure 3. On-State Characteristics http://onsemi.com 4 Figure 5. Hold Current Variation MAC16D, MAC16M, MAC16N 100 VGT, GATE TRIGGER VOLTAGE (VOLT) IGT, GATE TRIGGER CURRENT (mA) 1 VD = 12 V RL = 100 W Q2 Q3 Q1 Q1 Q3 Q2 VD = 12 V RL = 100 W 1 -40 -10 20 50 80 TJ, JUNCTION TEMPERATURE (C) 110 125 0.5 -40 -10 +20 50 80 TJ, JUNCTION TEMPERATURE (C) 110 125 Figure 6. Gate Trigger Current Variation dv/dt , CRITICAL RATE OF RISE OF OFF-STATE VOLTAGE(V/ s) Figure 7. Gate Trigger Voltage Variation 5000 4K VD = 800 Vpk TJ = 125C 100 (dv/dt) c , CRITICAL RATE OF RISE OF COMMUTATING VOLTAGE(V/ s) 3K 10 TJ = 125C 100C 75C 2K ITM tw VDRM f= 1 2 tw 6f ITM 1000 1K 0 (di/dt)c = 10 100 1000 RG, GATE TO MAIN TERMINAL 1 RESISTANCE (OHMS) 10000 1 10 20 30 40 50 60 70 80 90 100 (di/dt)c, RATE OF CHANGE OF COMMUTATING CURRENT (A/ms) Figure 8. Critical Rate of Rise of Off-State Voltage (Exponential Waveform) Figure 9. Critical Rate of Rise of Commutating Voltage LL 200 VRMS ADJUST FOR ITM, 60 Hz VAC TRIGGER CHARGE CONTROL TRIGGER CONTROL MEASURE I 1N4007 CHARGE - + MT2 1N914 51 W G MT1 200 V NON-POLAR CL Note: Component values are for verification of rated (di/dt)c. See AN1048 for additional information. Figure 10. Simplified Test Circuit to Measure the Critical Rate of Rise of Commutating Current (di/dt)c http://onsemi.com 5 MAC16D, MAC16M, MAC16N PACKAGE DIMENSIONS TO-220AB CASE 221A-09 ISSUE AA -T- B 4 SEATING PLANE F T S C NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. DIM A B C D F G H J K L N Q R S T U V Z INCHES MIN MAX 0.570 0.620 0.380 0.405 0.160 0.190 0.025 0.035 0.142 0.147 0.095 0.105 0.110 0.155 0.018 0.025 0.500 0.562 0.045 0.060 0.190 0.210 0.100 0.120 0.080 0.110 0.045 0.055 0.235 0.255 0.000 0.050 0.045 --- --- 0.080 MILLIMETERS MIN MAX 14.48 15.75 9.66 10.28 4.07 4.82 0.64 0.88 3.61 3.73 2.42 2.66 2.80 3.93 0.46 0.64 12.70 14.27 1.15 1.52 4.83 5.33 2.54 3.04 2.04 2.79 1.15 1.39 5.97 6.47 0.00 1.27 1.15 --- --- 2.04 Q 123 A U K H Z L V G D N R J STYLE 4: PIN 1. 2. 3. 4. MAIN TERMINAL 1 MAIN TERMINAL 2 GATE MAIN TERMINAL 2 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: N. American Technical Support: 800-282-9855 Toll Free Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Phone: 81-3-5773-3850 Email: orderlit@onsemi.com ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. http://onsemi.com 6 MAC16D/D |
Price & Availability of MAC16NG
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |